I was experimenting with my phone and flashed it over to cricket using a few simple steps, MMS / TALK/ TEXT / PIX working on $55 plan, Im not sure if this method has been posted so I thought I might share.

I have a feeling that I might have gotten lucky but maybe it might work for you.

You will need to download & install a couple of items which are mostly located @ step 2 link (except for RSD LITE ) :

- Motorola Drivers (specific to your platform 32 or 64 bit)
- RSD LITE 4.9 (step 1)
- Harware Virtual Serial Port
- CDMA WorkShop 2.7
- PRL (IM USING PRL 35568 FOR SAN ANTONIO, TX )
-
android - whiterabbit.org




(DOWNLOAD AND INSTALL EVERYTHING ABOVE BEFORE YOU BEGIN)

1. > SBF MY PHONE BACK TO ORIGINAL 2.2 ANDROID

Complete Droid X .sbf Flashing Guide




2. > THEN IS USED INSTRUCTIONS FOR CDMA POSTED BELOW OR VISIT LINK (quoted below THANKS TO CHRISNGROD) .
http://www.cricketusers.com/verizon-...#axzz1f0jZbYJ5

5) You should have found and installed CDMA Workshop 2.7
6) In HW Virtual Serial Port:
1. Boot the phone up regularly without the cable attached. There is no special button to press while booting.
2. Connect the phone to the PC with a USB data cable.
3. Slide down the notification bar and click on USB Connection row.
4. Make sure the phone is set to PC Mode
5. If you have the Android SDK kit on the PC the drivers should install automatically, or be pulled from the phone. If not there are some attached to this post.
6. Now Download and Install HW Virtual Serial Port CLICK HERE
7. Once you have it downloaded and installed open it up.
8. Click the Login button. The password should automatically be filled in and click OK.
9. Go to the Settings tab & make sure that NVT Enabled is unchecked & go back to the Virtual Serial Port tab.
10. To be safe, pick a COM port above 8.
11. Make sure the IP Address field reads 192.168.16.2 and the Port field reads 11008
12. Click the Create COM button and after a few moments you should now have successfully created a COM port for your Droid X.

If you get Error in the LAN Status field then you have not successfully installed the drivers for the phone, or the phone is not set in PC Mode.






7) Open up CDMA Workshop 2.7
8) Under COM Settings (AT Mode) select the COM port you setup from the tutorial and then click the connect button. If it successfully connected it will say Connected to COM15 port successfully. on the bottom (may not say COM15, thats just the port I used.)
9) Go to the Security tab and under SPC there will be an empty box. Enter 000000 then click the SPC button and Send. It will then popup saying SPC is correct. Phone unlocked.
10) Now go to the Other tab. Under PRL click Write and browse to where you put that PRL from earlier.

(IM USING PRL 35568 FOR SAN ANTONIO, TX )
11) Go to the NAM tab and in the MIN and MDN(Dir_Number) boxes enter in the info you got from cricKet customer service and click write.
12) Now go to the Memory tab. Under NV Items click Write. Browse and select the NV Item file you generated earlier. Once its done it will say 12 NV Items were successfully written to the phone.
13) Go to the Main tab. Click Mode>Reset
14) Your phone should have reset. Once it boots backup make sure to get your COM port back up and running.
15) You may now close CDMA Workshop 2.7 .


3. > AFTER YOU HAVE DONE THAT, & IT IS WORKING FOR YOU, ON YOUR PHONE GO TO:
SETTINGS > ABOUT PHONE > SYSTEM UPDATES
TO GET THE GINGERBREAD UPDATE DIRECTLY FROM MOTOROLA.

4. > Dial *228 TO MAKE IT OFFICIAL, KEEP IN MIND YOUR MEID HAS TO BE ON YOUR PLAN IN ORDER FOR YOUR PHONE TO PROGRAM.


If this does not work for you, I'm sorry, but there are other methods within this forum, this is what worked for me.